1. जब मूल आयाम के एक तरफ टॉलरेंस दी जाती है, तो यह _______ कहलाता है / When tolerance is given on one side of the original dimension, it is called _______.
Ans:- A
2. ___________आकार की अधिकतम सीमा और आकार की न्यूनतम सीमा के बीच का अंतर है / ___________ is the difference between the maximum size limit and the minimum size limit.
Ans:- A
3. अंतर्विनिमेयता आमतौर पर__________के लिए लागू होती है|
Ans:- B
4. निम्नलिखित मे से कौन सा सबसे कठोर कर्तन औजार सामग्री है / Which of the following is the hardest cutting tool material
Ans:- B
5. निम्नलिखित में से कौन सा कर्तन औजार एल्युमीनियम ऑक्साइड से बना होता है?
Ans:- D
6. ट्रिपल प्रारम्भ चूड़ी पर लीड, पिच से_________होती है / The lead on the triple starting Thread is _________ off the pitch.
Ans:- B
7. वर्नियर बेवल प्रोटेक्टर का प्रयोग________ मापन के लिए किया जाता है / Vernier bevel protector is used for ________ measurement.
Ans:- A
8. दुर्घटना से बचने का सर्वोत्तम तरीका क्या है / What is the best way to avoid an accident.
Ans:- A
9. एक मीट्रिक माइक्रोमीटर में, थिम्बल का एक पूरा चक्कर ________ आगे बढ़ता है / In a metric micrometer, a full circle of thimble moves ________.
A. 0.01 mm
B. 0.25 mm
C. 0.50 mm
D. 1.00 mm
Ans:- C
10. भारतीय मानकों के अनुसार, स्लिप गेज का एक ख़ास सेट प्रयोग किया जाता है जिसमें _______ होते हैं / As per Indian standards, a special set of slip gauges is used which consists of _______.
Ans:- B
11. हेक्सा ब्लेड के निकटस्थ दांतों के बीच की दूरी को ब्लेड की_______ के रूप में जाना जाता है।
Ans:- A
12. हाफ नट क्रियाविधि __________ मशीन में पायी जाने वाली एक क्रियाविधि है।
Ans:-D
13. निम्नलिखित में से कौन सा लेथ सेन्टर का एक प्रकार है / Which of the following is a type of lathe center.
Ans:- D
14. एक 50 मिमी. की बार को 25 मीटर/मिनट की गति पर एक खराद पर टर्न ऑन किया जाना है| rpm की गणना करें / A 50 mm. The bar is to be turned on a lathe at a speed of 25 m / min. calculate rpm .
Ans:- C
15. एक खराद पर मल्टी-स्टार्ट चूड़ियाँ काटने के लिए इनमें से किसका प्रयोग किया जायेगा?
Ans:- C
16. रफ़ टर्निंग टूल का प्रयोग आमतौर पर कब किया जाता है? When is rough turning tool normally used?
Ans:- B
17. सेट ओवर विधि द्वारा टेपर काटने के दौरान निम्नलिखित में से कौनसा सेंटर उपयुक्त होता है? Which one of the following centres is suitable while cutting taper by set over method?
Ans:- A
18. चिप ब्रेकर का कार्य ______ होता है| The function of chip breakers is to:-
Ans:- C
19. एक खराद उपकरण का फ्रंट क्लीयरेंस कोण 8° और बैक रेक कोण 15° है, इसका वेज कोण होगा A lathe tool has front clearance angle of 8° and back rake angle of 15°. Its wedge angle will be
Ans:- A
20. कारक जिसका कटाई गति के चुनाव पर कोई प्रभाव नहीं होता वह है The factor which has no influence on the selection of the cutting speed is
Ans:- C
21. नर्लिंग सामान्यत: ______ स्पिंडल गति पर की जाती है| Knurling is done generally at ______ spindle speed.
Ans:- C
22. एक कोणीय वर्कपीस पर पलस्तर किया जाना है| इसे _________ पर लगाया जाना चाहिए| An angular workpiece is to be faced. It should be mounted on
Ans:- D
23. एंगल प्लेट बनाने के लिए निम्न में से किस सामग्री का उपयोग किया जाता है? Which of the following material is used for making angle plate?
Ans:- C
24. सिंगल पॉइंट टूल का प्रयोग कर खराद पर चूड़ियाँ काटने के दौरान, टूल ________ कहलाये जाने वाले पाथ में चलता है| While thread cutting on a lathe by using single point tool, the tool moves in a path called as
Ans:- C
25. निम्नलिखित में से कौन सा एक टेपर टर्निंग की विधि है? Which of the following is a taper turning method?
Ans:- D
26. एक साइन बार का प्रयोग ________ को मापने के लिए किया जाता है| A sine bar is used to measure
Ans:- B
27. इस्पात पैमाने की रीडिंग सटीकता होती है| The reading accuracy of steel rule is
Ans:- B
28. निम्नलिखित में से कौन एक अलौह धातु है? Which of the following is a non-ferrous metal?
Ans:- D
29. निम्नलिखित में से कौन सा वर्नियर ऊंचाई गेज का एक हिस्सा है? Which of the following is a part of vernier height gauge?
Ans:- D
30. एक्मे चूड़ी के लिए अंतर्गत कोण का मानहै| The value of included angle for acme thread is.
Ans:- C